This cable testing instrument can quickly detect the
short circuit,open circuit, dislocation, instant short and open
circuit of various cables.Such as one-to-many, many-to-many,
cross type, cables with switch and other special kinds of wires
all can be tested.
The G**8N cable testing machine has the functions of
automatically reading samples and automatic testing,
In the spot measurement mode, long press the leftmost read
to proce sample learning, at this time you can press
the up and down keys as needed to select which group of data
space you want to save, then short press the read key stores
the data of the learning sample cable.
Short press the leftmost read to read the data
of the stored sample cable to proce the test. (It can store
data of *5 sets of sample cable)
The test result will be prompted with sound and
light,
There are three setting modes for the sound according to
the needs:â‘ off â‘¡ correct prompt â‘¢ error prompt,
When the cables are correct shows the green light , when
error shows the red light,, and the LCD display shows the
corresponding test results.
This machine has a memory function, no need to re-learn
samples after power off, the instrument will work in the
state before power off.
Performance
Characteristics:
I.The working
mechanism of the G**8N wire tester is to continuously repeat
the test. Only when the wire is detected to be the same as the
sample line, the display will be correct. After the test wire
is removed, it will return to the display error port.
II.The main
function of the point-finding interface is to find points for
the maintenance of the wire and the test fixture, connect the
wire to the port, use the meter pen to test the other end of
the wire, and the LCD displays the corresponding port number
for the test, so that the wrong wire can be quickly found ,
This function requires lightly pressing the mode key to enter
the point-finding mode.
III.Read
function: â‘ Short press to read the stored sample data,
press the up and down s to select the group, and finally
press to confirm the selection and return to the test state.
â‘¡Long press to enter the study and store the sample data,
press the up and down s to select the group, and finally
short press to confirm (the LCD will display PASS at the same
time) and return to the test state.
IV.Mode key
function: â‘ Short press to enter the test mode
conversion. â‘¡Long press to enter the parameter setting, press
up and down to select the setting parameter, after setting,
save and return to the test state.
V.Swing mode:
access the same wire as the selected sample data group, if it
is correct, the timer will start timing, there is no problem
with swinging the wire within the set time, and the display is
correct.
VI.Segmentation
mode: Segmentation starts from the sample data group â‘ .
When setting several segments, you must first read the status
data of the wire for storage. For example, if it is divided
into four segments, the sample data group ①②③④ is
tested in sequence.
Product
Parameters:
|
Input Voltage:
|
DC ***5V
|
|
Working Current:
|
**0mA
|
|
Detection Current:
|
*5mA
|
|
Test Pins:
|
A port ≤*4 Pin, B port ≤*4 Pin
|
|
Test Items:
|
Short circuit, Open circuit, Dislocation
|
|
Weight:
|
2.2KG
|
|
Size:
|
**5***5***5mm
|
|
Cable Correct Prompt:
|
Indicator light + Buzzer
|
|
Error Indication:
|
Corresponding indicator light (each indicator
corresponds to one bit)
|
|
Reset Switch:
|
Yes
|
|
Reverse Connection Protection:
|
Yes
|
|
Point-finding Function:
|
Yes
|
Operation Procedure:
â‘ Insert the power adapter into the DC power
interface on the back of the instrument
â‘¡Turn on the front panel switch, the power indicator
on the panel lights up. The tester enters the test state
â‘¢When the wiring harness to be tested is not
connected, the LCD displays the wrong test port
â‘£Connect the wire harness to be tested to the
instrument panel interface through a fixture or a flat cable
⑤Correct wire LCD shows that the wire is correct
â‘¥The wrong cable shows the wrong port number, and the
panel indicator shows at the same time
Note:
1. This wire tester instrument is suitable for standard test
(i.e. testing wire with no holes, standard two-terminal
conduction, terminal A and B and bilateral conduction test).
2. When the test is abnormal, you can use the probe to find
the function to see if the fixture is intact.
3. The cable testing instrument must be clean and hygienic,
and the operation table is neat and clean. In case of sudden
power failure, the power supply should be turned off in time.
4. If you have any questions during the operation, please
contact us, or contact customer service online communication.
5. Different wiring harness terminals are different. In
addition to purchasing our ready-made harness, customers can
make their own harness according to the types of harness
terminals.
