タイトルまたは説明
Automatic Incubator Applications: The equipment used for hatching
chickens, ducks, geese, pigeons, quails and other rare birds and
poultry. Technical parameters: Voltage: **0 V +/- *0% Current: *0
HZ Temperature range: *0 - *0 degree C Accuracy: +/- 0.1 degree C
Humidity range: *0 - *0% Turning egg angle: *5 degree C One, The
characteristics of the equipment: 1, High economic efficiency, as
the main sources of heat to electricity, coal to add sources of
heat, this machine can be used briquettes, briquettes, Meibing,
charcoal, gas and other fuels, can also be used to replace the hot
water method to maintain constant temperature. 2, Be not afraid of
power failure: automatic control with power, monitored by people
when power failure. After the blackout could be long-term normal
operation. 3, Safe and reliable: The water in the heater is heated
by the stove first, steam and hot water enter into the water plate
through the pipe, stoves and machines are separate, there is not
smell inside of the machine. The machines are installed with high
temperature insulation nickel chrome plastic packets of fever for
temperature. 4, The above layer of machine for incubating, the
below layer of that for animals out. Two, The main technical
indicators: 1. Temperature display range: 5 ~ *0 degree C 2.
Temperature accuracy: +/- 0.1 degree C 3. Humidity display range
:***9% RH 4. Humidity accuracy: +/- 5% RH 5. Output terminals: 7
Road (Excess-temperature, temperature control, low temperature,
left turning eggs, right turning eggs, wet control, alarm) 6.
Output current: temperature control, low temperature 6A, other 1A ,
7. Turning eggs frequency: **9, the largest recorded. 8. Turning
eggs cycle: 0.1 to *9.9 hours adjustable (pre-set at 1.5 hours) 9.
Turning eggs time: 1 to **5 seconds adjustable (factory set at **0
seconds) *0. Ventilation time: ****9 minutes (adjustable, pre*0
hours, no ventilation) *1. Ventilators time: ****9 seconds
(adjustable, factory set *0 seconds) *2. Measurement of lines:
about 1.5 meters Three, The working conditions: 1. Voltage: AC **0
V ~ **0V, *0HZ 2. Relative Humidity: less than *5% 3. Ambient
temperature: **0 degree C ~ *0 degree C Four, temperature and
humidity settings, for example: If an incubator requires
temperature *7.9 degree C ~ *8 degree C, humidity *5% ~ *0% RH.
Click on, , the temperature screen will display PPP, when the
humidity screen is off, loose the , temperature screen will
display the three figures for the value of the original incubation
temperature settings, if you want to change, cles, the max.
temperature is *8 degree C. Then press the , the temperature
screen will be off, humidity screen will display the three figures
for the value of the original incubation humidity settings, if you
want to change , click or to adjust the figures, the max.
humidity is *0% RH. Then press SET for 1 second until FFF
flash twice, which means the setting information be saved, then
loose the , the machine will automatically return to normal
working condition. Five, Arbitrary temperature and humidity
settings, for example: Click Set , machine will show PPP,
continue to hold down the , click to display P1 then loose
the , the left shows three figures for over-temperature
alarm. the machine will alarm when the temperature reaches this
value. Click to adjust the figures show that the value you
need. Then press Set , machine will display P2 then loose the
. Shows three figures for over-temperature value, The fan
will start when the temperature reaches the value. Click or
to adjust the figures show that the value you need. Then press Set
, machine will display P3 then loose the . Shows three
figures for the temperature control on the limit. The machine will
stop heating when the temperature reaches the value. Click
to adjust the figures show that the value you need. Then press Set
, machine shows P4. Shows three figures for temperature
control under the limit. The machine will start heating when the
temperature reaches the value. Click or to adjust the
figures show that the value you need. Then press , machine
shows P5. Shows three figures for the value of ***** machine will
start heating of the backup heater when the temperature droppes to
the value. Click or to adjust the figures show that the
value you need. Then press Set , machine shows P6. Shows
three figures for under temperature ***** machine will alarm when
temperature reaches the value. Click or to adjust the
figures show that the value you need. Then press Set ,
machine shows P7. Shows two figures for exceeding humidity *****
machine will alarm when humidity reaches the value. Click or
to adjust the figures show that the value you need. Then press Set
, machine shows P8. Shows two figures for stopping
humidifying. The machine will stop humidifying when the humidity
are more than the value. Click or to adjust the figures show
that the value you need. Then press Set , machine shows P9.
Shows two figures for starting humidifying. The machine will start
humidifying when the humidity is less than the value. Click or
to adjust the figures show that the value you need. Then
press Set , machine shows Pa. Shows two figures for low
humidity alarm. The machine will alarm when the humidity reaches
the value. Click or to adjust the figures show that the
value you need. Arbitrary temperature and humidity has been set up,
and then press the Set and keep for one second until FFF
flashing twice on the screen, which means the setting information
is saved, then the machine automatically returns to normal working
condition. Six, The settings for turning eggs: At the same time,
press the Set and Reduce†keys, the machine will display PPP,
continue to hold down the , click to display F1 then loose
the . The left shows three figures for the total number of
eggs up, which will be lost for power failure, the number will
start from zero when get the power again. Click , the total
number of eggs up will be cleared. Then press Set , when
display F2 then loose the , show 3 figures which is turning
eggs cycle time (unit:hour), factory set 1.5 hours. Click or
to adjust the figures. Turning eggs cycle time 0 means not turning
eggs. Then press Set , when display F3 then loose the
, show 3 figures which is turning eggs time (unit:second),
factory set **0 seconds. Click or to adjust the figures.
Then press Set , when display F4 then loose the , show
3 figures which is ventilation cycle time (unit:hour), factory set
0 hour. Click or to adjust the figures. Ventilation cycle
time 0 means: do not ventilate. Then press Set , when
display F5 then loose the , show 3 figures which is
ventilation time(unit:second), factory set *0 seconds. Click or
to adjust the figures. Seven, Manual turning eggs: Directly
press on the key can turn eggs slightly, the turning direction will
be determined by the computer automatically. Eight, The function of
temperature and humidity calibration: Hold down key to start the
machine , Display EEE means enter into the calibration function,
and the temperature will display, click or to adjust the
figures to match the standard temperature. Then press SET key, the
temperature display will be off, and the humidity display will be
on, click or to adjust the figures to match the standard
humidity. Then press SET key for 1 second until FFF flash twice,
which means the setting information be saved, then loose the
, the machine will automatically return to normal working
condition. The relative humidity can be adjusted with small
screws-driver to whirl the POT in the small hole of the humidity
sensor. Nine, Self-test function: Can not self-test with load. Hold
down key to start machine, seven output relayes pull in and release
in turn. Click can return to normal working condition. Ten,
Rapid return to the status of the original factory settings Hold
down the SET key to start the machine until FFF flasheing, setting
restore the original status, the temperature is *8 degree C,
humidity *0% RH, turn eggs cycle 1.5 hour, turn eggs time **0
seconds, ventilation time 2 hours, ventilation time 0 Seconds (stop
ventilators). Then automatically return to normal work.
国: |
China |
モデル番号: |
-
|
离岸价格: |
(交渉可能)
Get Latest Price
|
ロケーション: |
- |
最低注文量の価格: |
- |
最低注文量: |
1 |
パッケージの詳細: |
- |
納期: |
7-15days |
供給能力: |
150 |
支払いタイプ: |
- |
製品グループ : |
- |