engine diagnosis scanner tool Vcads 88890180/vcads 88890200 with PTT software used for volvo

タイトルまたは説明

engine diagnosis scanner tool Vcads *******0/vcads *******0 with PTT software used for volvo



Volvo vcads *******0 interface with PTT  /*******0 volvo vcads pro  in development model

 

Set includes:

Volvo Interface *******0;

USB cable;

*******7 8 Pin Cable;

VCADS  /PTT  Software DVD (in development model)

 

Languages:  english, cesky, dansk, Deutch, Espalol, Francis, Italiano, Magyar, Nederlands, Polski, Portuges, Romana, Srpski, Svenska, Turkce, Russian, Lietuva



 

Support Brand :

All Volvo Bus, truck, construction

 

Volvo vcads  , Volvo *******0 interface with PTT  /*******0

The *******0 communication unit enables PC to vehicle communication. The device connects to the PC via a USB cable or by wireless LAN using the **2.*1 b/g standard.

Operating temperature range: **0 to **5°C (**0 to ***5°F).

Storage temperature range: **0 to ***5°C (**0 to **7°F).

Before the *******0 communication unit can be used, a driver must be installed on the PC. In addition, a utility application (Admin***0) can be used to check the status of the device and update the firmware if and when needed.

There are three different ways, described below, of connecting communication unit*******0.

Via USB-cable

Connect the communication unit to the vehicle.

Connect the USB-cable between the communication unit and the PC.

Select communication unit *******0 and USB-cable setting in window Alternative.

Directly to the communication unit

Connect the communication unit to the vehicle.

Select communication unit *******0 and Direct to communication unit in window Alternative.

Security level Directly to the communication unit

Communication is performed using **8 bit WEP, Wired Equivalent Privacy. The WEP-key is generated automatically and is not seen during the configuration.

Via an access point

Note: Contact the local IT-support or network technician before installation.

Connect the communication unit to the vehicle.

Select communication unit *******0 and Via an access point in window Alternative.

Security level Via an access point

There are three alternatives for this:

WEP and MAC-address. Communication is performed using **8 bit WEP, Wired Equivalent Privacy. The WEP-key is written in during configuration. The MAC-address is to be written into the access point for additional security.

WPA and PSK. Communication is performed via WPA, Wi-Fi Protected Access.

**2.1x. Communication is performed using standard EAP_MSCHAP v2. The communication unit is then treated as a PC and will be logged on to the network using a username and password.

Product description for communication unit *******0

Communication unit *******0 has a number of different coloured LEDs. These LEDs show the status of the communication unit and indicate warnings, etc.

*******0 Communication Unit with protective cover

The Communication Unit *******0 (previous parts number *******0) is used to enable communication between a computer and a vehicle/machine.

The Communication Unit *******0 includes a protective cover that encloses the wire connections and reduce situations where the unit loose connection with the vehicle

For detailed information regarding the Communication Unit , connection types , installation , LED’s description , fault tracing and software update , see the Tech Tool help.

Warranty

The Communication Unit has a *2 months warranty from delivery date. Please note the date when you received this product . This information is requires if the device needs to be replaced during the warranty .

How to send feedback

Please use your normal channels to report feedback and problems concerning the communication unit .

Connection types

There are three different ways of connecting the communication unit ; via USB cable . directly to the communication unit (wireless)or via access point (wireless) .The default connection type for the communication unit is via USB cable .

Update software (so called Firmware)

The Communication Unit includes software (so called firmware) that is updated on a regular basis . The updates are installed with Tech Tool DVD or in the network releases , and then needs to be downloaded to the Communication Unit through the Update software function . The Communication Unit must be connected both to a computer and a vehicle during the update .

RP***0 application support

The Communication Unit support the RP***0 . Other applications can use this device and perform vehicle/machine communication . The WLAN settings needs to be configured in the Tech Tool settings before you start your RP***0 application . The configurations , IP-addresses etc. are stored in an INI-file which can be used by other RP***0 applications . There is an off-line configuration application available on request ( only available in English).

Known problems

The installation procedure of the USb-driver for the communication unit will be performed the first time the unit is connected to a USB-port . This procedure will be repeated if the unit is connected to another USB-port on the same computer.

Checklist before returning a faulty product:

Check that all the LED sensors light up shortly when powering up the unit.

When connected only to USB: The unit should flash the LED sensors and then light the “power USB/Communication”-LED.

If the “power USB/Communication”-LED does not light up:

1. Try another USB-port

2. Check if windows performs “Installing device driver software”

3. Check the USB cable and try a different cable , or try another PC

4. If still no function, return the communication unit

When connected only to vehicle : The unit should flash the LED sensors and then light the “Power Vehicle”-LED .

If nothing light up:

1. Try replacing the vehicle cable.

2. Check that ignition is on , or try another vehicle.

If the “Critical Error” –LED is lit :

1. try to update the software .

2. If still no function , return the unit .

WLAN dose not work.

Consult your local IT support for advanced checking of WLAN.

Protective Cover *******0

The protective cover for Communication Unit *******0 is to reduce the possibility of losing connection with the vehicle or the PC via the USB cable.

The protective cover also protects the communication unit when it comes to acceleration damage (for example dropping ) as well as damage to the connectors .

CAUTION !

Only use the USB cable ( Parts no.*******4 ) with the correct connector dimensions , see picture .

 

1 Prepare the *******0 , remove the lock mechanism , rubber pads and USB connector (plug A and plug B).

2 Place the *******0 into the rubber protection .

3 Assemble the bracket.

Connect the vehicle and USB cable . Plug in plug A

Assemble the USB cable lock.

Assemble the vehicle cable lock .

4  The tool is now ready to use in the daily work .