离岸价格
Get Latest Price|
- Minimum Order
国:
China
モデル番号:
-
离岸价格:
ロケーション:
-
最低注文量の価格:
-
最低注文量:
-
パッケージの詳細:
-
納期:
-
供給能力:
-
支払いタイプ:
-
製品グループ :
China
連絡先担当者 Mr. Wilson
6-703, FUYUAN COMMUNITY, YUFU ROAD, LONGGANG DISTRICT, SHENZHEN, CHINA, Muping, Sichuan
Ethernet Shield
Module V2 0 Arduino Compatible
It is compatible with the Arduino Uno and Mega (using the Ethernet
library).
Download: Arduino-ethernet-shield***-schematic. Pdf,
arduino-ethernet-shield***-reference-design. Zip
Download: Arduino-ethernet-shield-schematic. Pdf,
arduino-ethernet-shield-reference-design. Zip
The Arduino Ethernet Shield allows an Arduino board to connect to
the internet. It is based on the Wiznet W***0 ethernet chip
(datasheet). The Wiznet W***0 provides a network (IP) stack capable
of both TCP and UDP. It supports up to four simultaneous socket
connections. Use the Ethernet library to write sketches which
connect to the internet using the shield. The ethernet shield
connects to an Arduino board using long wire-wrap headers which
extend through the shield. This keeps the pin layout intact and
allows another shield to be stacked on top.
The Ethernet Shield has a standard RJ**5 connection, with an
integrated line transformer and Power over Ethernet enabled.
The latest revision of the shield adds a micro-SD card slot, which
can be used to store files for serving over the network.
It is compatible with the Arduino Uno and Mega (using the Ethernet
library). The onboard microSD card reader is accessible through the
SD Library. When working with this library, SS is on Pin 4.
The latest revision of the shield also includes a reset controller,
to ensure that the W***0 Ethernet module is properly reset on
power-up. Previous revisions of the shield were not compatible with
the Mega and need to be manually reset after power-up. The original
revision of the shield contained a full-size SD card slot; This is
not supported.
The *-pin serial programming header is compatible with FTDI USB
cables and the Sparkfun and Adafruit FTDI-style basic USB-to-serial
breakout boards. It features support for automatic reset, allowing
sketches to be uploaded without pressing the reset on the
board. When plugged into a FTDI-style USB adapter, the Arduino and
Ethernet shield are powered off the adapter.
The current shield has a Power over Ethernet (PoE) module
designed to extract power from a conventional twisted pair Category
5 Ethernet cable:
1, IEEE**2.3af compliant
2, Low output ripple and noise (**0mVpp)
3, Input voltage range *6V to *7V
4, Overload and short-circuit protection
5, 9V Output
6, High efficiency DC/DC converter: Typ *%@********************, ***0V isolation ( to output)
The shield does not come with the PoE module built in, it
is a separate component that must be added on.
Arduino communicates with both the W***0 and SD card using the SPI
bus (through the ICSP header). This is on digital pins *1, *2, and
*3 on the Duemilanove and pins *0, *1, and *2 on the Mega. On both
boards, pin *0 is used to select the W***0 and pin 4 for the SD
card. These pins cannot be used for general I/o. On the Mega, the
hardware SS pin, *3, is not used to select either the W***0 or the
SD card, but it must be kept as an output or the SPI interface
won't work.
The shield provides a standard RJ*5 ethernet jack.
The reset on the shield resets both the W***0 and the
Arduino board.
The shield contains a number of informational LEDs:
PWR: Indicates that the board and shield are powered
LINK: Indicates the presence of a network link and flashes when the
shield transmits or receives data
FULLD: Indicates that the network connection is full duplex
**0M: Indicates the presence of a **0 MB/s network connection (as
opposed to *0 MB/s)
RX: Flashes when the shield receives data
TX: Flashes when the shield sends data
COLL: Flashes when network collisions are detected
国: | China |
モデル番号: | - |
离岸价格: | Get Latest Price |
ロケーション: | - |
最低注文量の価格: | - |
最低注文量: | - |
パッケージの詳細: | - |
納期: | - |
供給能力: | - |
支払いタイプ: | - |
製品グループ : | arduino board and accessories |