あなたはまだ TradeKey.com のメンバーではないようです。 今すぐサインアップして、世界中で700万を超える輸入業者および輸出業者と接続します。 今すぐ加入、無料 |
BOOK A CALL
Book Call On Your Favorite Time
Code
🗘

By Signing Up. I agree to TradeKey.com Terms of Use, Privacy Policy, IPR and receive emails related to our services

Contact Us
product
Prev
LED Decoration Light LED Decoration Light LED Decoration Light LED Decoration Light LED Decoration Light
Next

LED Decoration Light

离岸价格

Get Latest Price

100 ~ 1000 USD /

|

100 Piece Minimum Order

国:

China

モデル番号:

WJL-0021

离岸价格:

100 ~ 1000 USD / Get Latest Price

ロケーション:

guangzhou

最低注文量の価格:

100

最低注文量:

100 Piece

パッケージの詳細:

carton package

納期:

20 days

供給能力:

1000 Piece per Month

支払いタイプ:

PayPal, L/C, T/T

製品グループ :

-

今すぐお問い合わせください
無料会員

連絡先担当者 Mr. Frank

32-4-302 LONGXIANG STREET,TIAN CAI MING YUAN 6-3-201, Jinhua, Zhejiang

今すぐお問い合わせください

製品仕様

  • led wheel cover light:led auto chassis lamps
  • car led emblem:led side vent light
  • solar antenna led light:EL car trim light

タイトルまたは説明

With special design ,it's very easy to install and use. It's low power consumption and also can make your car to get a charming fancy look. It's a latest amazing car accessory. Most importantly, as a DIY fun, your can install it at home which bring lots of convenience to you.

 
Introduction of function:
1.This product should be installed in the original position to replace the original logo(at the back of the car)
2.High quality water plating car badge, Laser and Reflective mirror
3.When the license plate lamp is turned on,the car logo light will be turn on too, which shines the logo in the night .
4.Special waterproof and dustproof design!
 
Installation:
1.First, spread a towel beside the car trunk (in order not to scratch the car body), with a flat head screwdriver, pry the car logo
 
2.Tear off the double-sided adhesive: pry it from the car body with moderate strength, steps by steps, slowly pry it down, then clean up the logo and car body .
 
3.Use crosshead screw-driver to uninstall the board inner the trunk, There are clips at somewhere, please carefully remove the insulation board ,you can see all kinds of lines.
 
4.Pass the power line of Car logo lamp through one of the logo location hole, pass inside the trunk and tear off the back of vehicle logo light
 
5.As the car logo lamp has installed, now connect the power supply.The logo lamp should connected with the light power supply of the rear license plate ,so that when turn on the small night lamp, the car logo lamp is also turned on Find the license plate lamp power connector
 
6.First pull the plug, and strip a opening separately of the positive and negative pole to show the wire core, Connect the lines(red to red and black to black) ,don't forget to wind then with insulating tape, Also, you need to plug back and set the insulation board to the trunk again!

国: China
モデル番号: WJL-0021
离岸价格: 100 ~ 1000 / Get Latest Price
ロケーション: guangzhou
最低注文量の価格: 100
最低注文量: 100 Piece
パッケージの詳細: carton package
納期: 20 days
供給能力: 1000 Piece per Month
支払いタイプ: PayPal, L/C, T/T
製品グループ : -

Send a direct inquiry to this supplier

To:

Mr. Frank < ZHEJIANG LEDAUT AUTO PARTS & ELECTRONICS CO., LTD >

私は知りたい: