タイトルまたは説明
MAIN STRUCTURE AND THE FEATURES
1.The machine is composed by the
box-seat, universal bearings, fly lose, chassis, belt lose,
blanking network support, knife-axis, the activities of the blade,
a fixed blade, feed doors, and the car containing
material,Spindle
and blades rotate around the V-belt controlled by the motor. The
material is crushed by the free blades on the spindle and the fixed
blades on the box.
2. The cutter is imported from
Japan, which can be used for a long time. The machine can be
separated into several independence parts. Then, it is easy for you
to check and clean. And also it has a double-deck structure,
equipping with the sound insulation materialwhich can make the
noise lower.
INSTALLATIONINSTRUCTIONS
1. The machine adopts the
three-phase power, and plugs into the appropriate voltage according
to the show of data plate, then, it connects the ground
wire.
2. After fixing the machine into a
appropriate position, you must fix and lock the a real wheel to
avoid making some noise when you move the
machine.
3. This machine is equipped with
the safe micro switch, which is regarded as a security protector to
keep off the wrong operation while overhauling. When the machine is
installed, users should device independent switch in order to cut
off the power and avoid the operating accident etc.
4. The machine is equipped with the
water-cooling system, two water pipes are in order to enter water,
surface, connect the running water pipe according to the
mark.
BEFORE USING YOUR GRANULATORS
1. The preparation before using:
According to the granularity of need, adjust the interval of razor
blade; use the screen mesh of different aperture
first.
A. Open the charging door and
blanking network support, check whether there is odds and ends or
metal material in the pulverize room.
B. Check the rotator razor blade
and revitalize the interval of the fixed cutting edge, the razor
blade fastens the bolt to lock, whether the spring washer plays a
role in compressing tightly.
C. Rotate flywheel with hand,
check, it operates to be normal.
D. Check it is firm that the feed
inlet glue board is connected with charging door, compress tightly
the nut to lock.
E. The bearing on the main shaft
should pour into enough lubricating oil to chew.
2. The operation
A. operator of the machine must be
familiar with the knot machine of the machine and operation
principle.
B. check to it turns to be correct
electrical machinery (chew and point out according to belt arrow
covered to protect)
C. checks whether the elasticity
intensity of the V belt is appropriate.
D. starts the machine for five
minutes air transport rotates, it is normal that checks and
operates.
E. machine work, operator should
take, protect glasses and ear put on, should also feed inlet both
sides feed in raw material in machine; make sure not to be facing
the reinforced mouth.
NOTICE
1 Of safety in operation of the
pulverizer. It feeds to be should appropriate, avoid, put a large
number of into or too big plastic lead to the fact card hinder now
as take place Carlos hinder and should shut down immediately, it
should be even to throw the material, prevent machine burden from
being overweight and result in damaging.
2. Find the cutting edge should
repair or change the razor blade in time while having blunt mouths
or damaging.
3. Pay attention to the motor
bearing situation of generating heat at any time, temperature can't
exceed *0 degrees C.
4. Forbade throwing the material in
6 minutes before shutting down, the ones that treated in the
pulverizer room stored the material and can shut down after totally
crushing.
5. It is difficult for plastic not
to enter pulverizer at the room, make sure not, bulldoze with hand,
with accident, should shut down, clear up or in charge of, dredge
dish with plastic.
6.
Forbid having metal part and hard supplies in the broken thing, so
as not to cause the razor blade and mechanical
damage.
OPERATING YOUR GRANULATORS
1. While adjusting the razor blade,
based on fixed razor blade, adjust the razor blade of the activity,
its relative interval is 0.**0.8mm, the following broken plastic
all kinds of, razor blade interval test form:
|
Seq.
|
Plastic Size
|
Cutter Clearance
|
Cutter Size
|
|
1
|
plastic thin
slice
|
0.3mm
|
Flat/Claw Cutter
|
|
2
|
Soft Plastic
|
0.**0.5mm
|
Flat Cutter
|
|
3
|
Hard Plastic
|
0.**0.6mm
Screen stencil
aperture<=Ø**8mm
0.**0.6mm
Screen stencil
aperture<=Ø
***0mm
|
Claw Cutter
|
| 国: |
China |
| モデル番号: |
NPM-V5000-SC
|
| 离岸价格: |
1000 ~ 20000 / Set ( Negotiable ) （交渉可能）
Get Latest Price
|
| ロケーション: |
China |
| 最低注文量の価格: |
1000 per Set |
| 最低注文量: |
1 Set |
| パッケージの詳細: |
Standard wooden case |
| 納期: |
5 days after receiving deposit |
| 供給能力: |
1000 Set per Month |
| 支払いタイプ: |
T/T, Western Union, Other |
| 製品グループ : |
Plastic Crusher
|
