タイトルまたは説明
A3WGFDHGF
A3WG7 resin is a *5% glass fiber
reinforced injection molding PA*6 grade for machinery components
and housings of high stiffness and dimensional stability
- Advantages:
- *5% glass fibers reinforced
- Good resistance
- Good flow ability
- Good heat-ageing stabilized
- Good suitability to surface treatments
- Typical applications/end uses:
- Used in many industries eg automotive, E and E, medical, house
appliance, good mechanical properties and process-ability also are
suitable for various structural parts
- Processing guidelines:
- Material handling:
PA (nylon) materials must be properly dried in order to provide
parts with optimum strength and toughness, nylon materials are
hygroscopic and will become degraded by excessive moisture during
the injection molding process
Products are supplied in moisture-protected containers and drying
prior to molding is not required, if drying becomes necessary,
dehumidifying or desiccant dryer operating at *0°C is recommended,
drying time is dependent on moisture level, but **6 hours is
generally sufficient Make sure final moisture content must be less
than 0.2%
Melt temperature: **0 to **0°C
Mold temperature: *0 to *0°C, but temperatures of as low as *5°C
and as high as **5°C can be used where applicable
Injection pressure: ****0MPa
Fast fill rates are recommended to ensure uniform melt delivery to
cavity and prevent premature freezing
Surface appearance is directly affected by injection rate
7 resin is a *5% glass fiber reinforced injection molding
PA*6 grade for machinery components and housings of high stiffness
and dimensional stability
- Advantages:
- *5% glass fibers reinforced
- Good resistance
- Good flow ability
- Good heat-ageing stabilized
- Good suitability to surface treatments
- Typical applications/end uses:
- Used in many industries eg automotive, E and E, medical, house
appliance, good mechanical properties and process-ability also are
suitable for various structural parts
- Processing guidelines:
- Material handling:
PA (nylon) materials must be properly dried in order to provide
parts with optimum strength and toughness, nylon materials are
hygroscopic and will become degraded by excessive moisture during
the injection molding process
Products are supplied in moisture-protected containers and drying
prior to molding is not required, if drying becomes necessary,
dehumidifying or desiccant dryer operating at *0°C is recommended,
drying time is dependent on moisture level, but **6 hours is
generally sufficient Make sure final moisture content must be less
than 0.2%
Melt temperature: **0 to **0°C
Mold temperature: *0 to *0°C, but temperatures of as low as *5°C
and as high as **5°C can be used where applicable
Injection pressure: ****0MPa
Fast fill rates are recommended to ensure uniform melt delivery to
cavity and prevent premature freezing
Surface appearance is directly affected by injection rate
Note:
Although all statements and information in this publication are
believed to be accurate and reliable, they are presented gratis and
for guidance only and risks and liability for results obtained by
use of products or application of suggestions described are assumed
by the user, no warranties of any kind, either express or implied,
including warranties of merchantability or fitness for particular
purpose, are made regarding to the products
ADDFPolyplastics
POM Duracon GH**5D Acetal Co-polymer with *@********************ANG PLASTIC TECHNOLOGY CO., LTD.
GF *5% reinforced, High strength, High rigidity
DURACON® is a crystalline thermoplastic acetal copolymer. The
primary raw material trioxane, a trimer of formaldehyde.
The thermoplastic adopts a copolymer structure in which
polyoxymethylene (-C-O) and carbon-carbon (-C-C- bond) comonomer
groups are incorporated into its main chain. Therefore the
copolymer has superior chemical and thermal stability, compared
with acetal homopolymer.
Acetal co-polymer is well-balanced in terms of mechanical, chemical
and thermal properties, and its superior moldability allows it to
be widely employed in various industrial fields
| 国: |
China |
| モデル番号: |
A3WG7
|
| 离岸价格: |
2 ~ 3 / Kilogram ( Negotiable ) （交渉可能）
Get Latest Price
|
| ロケーション: |
China |
| 最低注文量の価格: |
2 per Kilogram |
| 最低注文量: |
25 Kilogram |
| パッケージの詳細: |
25KG/BAG |
| 納期: |
15~30days |
| 供給能力: |
- |
| 支払いタイプ: |
T/T, L/C, Western Union |
| 製品グループ : |
PA
|
