离岸价格
Get Latest Price4 ~ 100 / Kilogram ( Negotiable )
|1 Ton Minimum Order
国:
Turkey
モデル番号:
-
离岸价格:
4 ~ 100 / Kilogram ( Negotiable )Get Latest Price
ロケーション:
TURKISH
最低注文量の価格:
4 per Kilogram
最低注文量:
1 Ton
パッケージの詳細:
BUCKETS
納期:
14 DAYS
供給能力:
50 Ton per Day
支払いタイプ:
T/T, L/C
製品グループ :
-
Turkey
連絡先担当者 Mr. Ismail
OSMANGAZI MAHALLESI 2638.Sokak No: 4/3, ESENYURT, ISTANBUL
Appearance
Part A (Epoxy Resin): Liquid Transparent
Part B (Epoxy Hardener): Liquid Pale Yellow
Packaging
Part A: *3.6 kg. net Part B: 6.4 kg. net
Total: Part A+B: *0 kg. net Part A+B: *2.*5 kg. gross
Part A: 2.*2 kg. net Part B: 1.*8 kg. net
Total: Part A+B: 4 kg. net Part A+B: 4.*0 kg. gross
*Barrels are available if requested.
Storage
Store in original sealed containers in a cool dry environment at
temperatures
between *5â°C and **0â°C. Do not put excessive loads on top of
the products, which would damage the packaging.
Shelf Life
Minimum *2 months from date of production if stored in original
unopened
containers. Once opened, product should be consumed within one week
as it is stored under appropriate storage conditions.
Chemical Structure
Part A : Epoxy Resin Part B: Epoxy Hardener
Technical Specifications
All technical values were calculated based on **3â°C and *0%
relative humidity. Temperature and humidity changes would change
technical values.
Tardigrade EPST **0 Technical Data
Density | Mixed Resin: 1.*8 kg/liter (± %3) |
Viscosity | Mixed Resin: ******0 mPa.s |
Shore D Hardness | 7 days: ****5 (ASTM D******5) |
Compressive Strength | *8 days: > *5 N/mm² (ASTM D*****0) |
Flexural Strength | 7 days: > *0 N/mm² (ASTM D**0) |
Bond Strength | 7 days : > 3 N/mm² (Concrete) (ASTM D***4) |
Abrasion Strength | 7 days : *5 mg (± %3) (CS *0/***0/***0) (ASTM D******4) |
Duration of Use After Mixing | ****0 minutes |
Total Curing Time | 7 days |
Preparation of Substrate
Concrete substrates must be sound and of sufficient compressive
strength (minimum *5 N/mm²) with a minimum pull off strength of 2,5
N/mm². The residual moisture content of the substrate must not
exceed 4%, the substrate temperature should remain a minimum of
*8â°C and the temperature of the substrate must be at least *3â°C
above the current dew point temperature.
The substrate must be clean, dry and free of all contaminants such
as dirt, oil, grease, coatings and surface treatments, etc.
Concrete substrates must be prepared mechanically using abrasive
blast cleaning or scarifying equipment to remove cement laitance
and achieve a profiled open textured surface.
If in doubt of the surface, apply a test area first. Do not apply
on wet or frozen surfaces and surfaces with high humidity.
Application Conditions
During the application, ambient temperature should be between
**0â°C and **0â°C. Relative Air Humidity should not exceed *0%
and the substrate temperature should be between **0â°C and
**0â°C. Substrate humidity should be maximum 4%. Substrate
temperature shouldnt be less than *8â°C and must be at least
*3â°C above the current dew point temperature.
Mixing
Make sure that the product temperatures are between **5â°C and
**5â°C before starting the mixing procedure. Prior to mixing, stir
part A and B separately with a mechanical drill and paddle at a
very low speed.
Add component B gradually into component A and mix till you reach a
homogeneous consistency (Approximately 3 minutes).
If it is going to be used as a repair mortar, please add aggregate
after mixing A and B components. Pour the contents into a clean
container and mix
for another couple minutes.
Please avoid mixing on high speed and do not add any solvent, etc.
into the mixture during the application procedure.
Application Procedure
Avoid application under excessive heat or wind, rain and/or when
the ambient and/or substrate temperature is below **0â°C or above
**0â°C. In extremely cold conditions, heaters should be used to
increase the ambient and the workability of the product.
After the mixing procedure, Tardigrade EPST **0 can be applied to
the surface by using brush, roller, trowel or squeegee. Make sure
that a continuous, pore free coat covers the substrate. Apply two
coats if necessary. Aggregate (******0 micron thick) is transferred
to the still wet primer in order to improve adhesion of the
following epoxy or PU coat.
Mixed product should be applied in max. *0 minutes in about
**0â°C. of waiting time between coats should be minimum *0 hours
in **0â°C and maximum *8 hours. If waited more than *8 hours, the
surface should be sanded.
The product would be completely cured in a minimum of 7 days to
reach its maximum mechanical and chemical resistance.
Reaction times of resin based systems depend on ambient and
substrate temperatures as well as relative humidity. Under lower
temperatures reaction times are longer and this increases pot life,
coating interval and working time. High temperatures increase
chemical reactions and the above mentioned time decreases
accordingly.
After application, the material should be protected from direct
contact with water minimum for *4 hours. Within this period,
contact with water can cause a surface carbonation and/or surface
tackiness, both of which must be removed. In such cases overall
coating should be removed from the floor and renewed.
Epoxy and polyurethane flooring systems, should be performed by
expert contractors.
Cleaning of Tools
Clean all tools and application equipment with thinner immediately
after use. Hardened/cured material can only be mechanically
removed.
国: | Turkey |
モデル番号: | - |
离岸价格: | 4 ~ 100 / Kilogram ( Negotiable ) Get Latest Price |
ロケーション: | TURKISH |
最低注文量の価格: | 4 per Kilogram |
最低注文量: | 1 Ton |
パッケージの詳細: | BUCKETS |
納期: | 14 DAYS |
供給能力: | 50 Ton per Day |
支払いタイプ: | T/T, L/C |
製品グループ : | - |