2014 VA-48 Fully Automatic Energy Saving Transparent Mini Chicken Egg Incubator

タイトルまたは説明

***4 CE Marked Mini Egg Incubators VA**8

 

 Incubator Characteristic

It is suitable for the families and specialized households to incubate chickens, birds, ducks and geese, etc. This machine is produced under strict CE test and has good reputation from the peasants in the rural area ,especially in eastern European countries. The machine has the characteristics of strong practicality, Easy operation and long service life, etc.
 

Incubator Product Function

 1) Automatic egg turning

 2) High and low temperature alarm, high and low humidity alarm

 3) Recorded days of incubation 

 4) Add water outside with free water dropper

 5) Lower cover is transparent, very easy to observe

 6) Easy to operate. Automatic temperature control and automatic display for temperature&humidity
 

1.1 Connect the egg turner plug to the control plug inside the egg compartment.

1.2 Connect the provided power supply to the back of the unit and your power source.

1.3 Switch on your power source.

1.4 Switch your unit on.

1.5 You will hear an alarm sounding due to low temperature/humidity.

1.6 Press any of the green s to cancel the alarm.

1.7 By opening the incubator and filling the water channels you will notice the humidity

      reading increase.

1.8 Let the unit run for 2 hours to note the egg turner turning.

 

2. Setting the temperature

2.1 Push “SET” once.

2.2 Push “+” or “-“ to select the desired temperature.

2.3 Push “SET” once more to exit.

- These incubators are factory set at *8oC, I found the chicks hatch at day *9 to 

  *0 meaning the temperature being to high. Using the method as described

  above. I recommend you set the temperature at *7.6oC.

 

3. Temperature alarm parameter settings (AL and AH)

The temperature alarm is factory set to sound at 1oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.

3.1 Low temperature alarm parameter setting. (AL)

3.1.1 Press and hold “SETT” for 3 sec.

3.1.2 Push “+” or “-“ until code “AL” appears in the temperature screen.

3.1.3 Push  “SET”

3.1.4 Push “+” or “-“ to adjust to your desired lower alarm setting.

 

3.2 Higher temperature alarm parameter setting (AH)

3.2.1 Press and hold “SETT” for 3 sec.

3.2.2 Push “+” or “-“ until code “AH” appears in the temperature screen.

3.2.3 Push  “SET”

3.2.4 Push “+” or “-“ to adjust to your desired higher alarm setting.

 

4. Humidity alarm parameter settings (AS)

The humidity is factory set to sound at *0% .

(Note: it can be adjusted according to your  incubating request.)

4.1 humidity parameter setting. (AS)

4.2 Press and hold “SET” for 3 sec.

4.3 Push “+” or “-“ until code “AS” appears in the temperature screen.

4.4 Push  “SET”

4.5 Push “+” or “-“ to adjust to your desired humidity.

- By filling both water channels depend on the  local humidity levels and the time of year, and how much water inside the incubator and humidity to determine whether it need to add water or not.

 

5. Calibrating temperature sensor reading (CA)

The thermometer correct reading is set at 0oC. The reading given by the thermometer can be adjusted if you find that the temperature reading is incorrect using a calibrated thermometer.

5.1 Calibrating the temperature sensor measurement. (CA)

5.2 Press and hold “SETT” for 3 sec.

5.3 Push “+” or “-“ until code “CA” appears in the temperature screen.

5.4 Push  “SET”

5.5 Push “+” or “-“ to adjust to the correct measurement.

- Note that the adjustment is the difference between the thermometer readings

  and should be adjusted with “- “ if the temperature reading of the incubator is to

  high and normal value (indicating + value) if the incubator reading is too low.

 

 

6. Temperature Upper and lower limit set (HS and LS)

HS - (High Set) and LS- (Low Set) set the limit of the setting range of the desired temperature setting (incubating temperature adjustment)

If HS is set as *8.2 and LS is set as *7.4, then the desire temperature (incubating temperature adjustment) can only be changed from *8.2 to *7.4, so the minimum temperature shall be limited to *7.2 even if the “-“ is kept on pressing. The same goes for the High Set Limit.

 

- This is to prevent accidental out of range temperature setting.

 

7. Heating Element (HU and HD)

Parameter HU and HD, set by factory and is not supposed to be modified by user.

HU -Default setting is *8 ( I believe it’s Heat Up power setting, controlling the start up power to the heater to bring it up to the desired temperature setting (incubating temperature adjustment). Setting Range 1~*0.

HD - Default setting is *1 ( I believe it’s Heat Down power setting, controlling the power to maintain the heater at the desired temperature setting (incubating temperature adjustment).

Setting Range 1~*0.

 

- These are settings I have never adjusted or attempted to adjust as the heating

  unit starts and stops within 1oC of my set temperature of *7.6oC.
 

Q: First time to buy things online overseas, how can I believe that you would send products?  

 

A: We are verified company by Alibaba and we have SGS inspection certificate, for the first time cooperation , there’s indeed trust problems between customers and suppliers , but don’t worry , we accept ESCROW payment . In future business cooperation , please consider T/T or western union as we know very well with each other and we are good partners and friends !

 

Q: How to ensure that I will receive the machine without any shipping damage?