Description

Product Description Product Model:GBS***8 Before use, paying attention to matters 1、In your installation before you read this brochure, please do not understand the statement before the operation began, there will be may not be able to use。 2、Before installing, please find out the way your video signal. Signal means (category) usually the following categories 　　 ï&frac*4;RGBï&frac*4;ˆSOG Green synchronousï&frac*4;‰ 3 BNC 　　　ï&frac*4;RGBSï&frac*4;ˆCS Composite syncï&frac*4;‰ã€€ 4 BNC 　　　ï&frac*4;RGBHVï&frac*4;ˆSeparation of synchronousï&frac*4;‰ 5 BNC 　　　ï&frac*4;CGA/EGAï&frac*4;ˆRGBSï&frac*4;‰ã€€Db9 to Db*5 Output Make sure that type of signal it will start the installation. 3、Interface structure of products. Mark the corresponding interface features: (below) DC*2V: Power input, *2V DC voltage, current proposals for more than 1A. RS**2: debug interface serial controller through the interface can be adjusted on the circuit boards and programming. VGA OUT: signal output interface, you can directly access the display. VIDEO IN 2: DB*5 connector, the signal input, channel 2. VIDEO IN 1 5BNC: input signal, channel 1. K1: Switch button, you can switch the signal input channel, and switch the input signal format. 4、Installation 1), interface introduced Under the panel: a channel signal input interface, for a total of five BNC, plus a button to switch K1. V: for the field synchronization signal. H / CS: for the line sync signal, or composite sync signal. R / Pr / Cr:: red signal, or the color of the PR, CR. G / Y: green signal, or the Y color difference signal. B / Pb / Cb: blue signal, or difference of Pb, Cb. K1: Switch button. Description of a channel interface, V H / CS R / Pr / Cr G / YB / Pb / Cb K1 (panel screen) When the signal source for the RGB (SOG green sync) then R / Pr / Cr, G / Y, B / Pb / Cb Three BNC, one-to-one. When the signal source for the RGBS (CS composite sync) then H / CS, R / Pr / Cr, G / Y, B / Pb / Cb four BNC, one-to-one. When the signal source to RGBHV (sync separation) then V, H / CS, R / Pr / Cr, G / Y, B / Pb / Cb five BNC, one-to-one. When the signal source for YUV and YPbPr when the next R / Pr / Cr, G / Y, B / Pb / Cb, one-to-one. On the panel: two-channel signal input interface such as VGA output. VGA in: not really a VGA input interface, the same RGB, color difference, EGA and other signal interface, but for the convenience of customers connected, especially the **-pin input customer. Plans are defined as follows: 2), connection diagram 5, button Description: 　 K1 key function: K1 key functions, menu for two, the first level for the channel selection and signal source selection. Such as: 1 channel RGB, *-channel RGBS. Resolution of two menu options for input, such as **0I, ***0P. The use of techniques, when click K1, a menu will appear, OSD prompted for the flash, when the OSD when prompted for the flash can be to switch the input channel K1. If the input channels are required to use, please wait a few seconds after the flash, the system automatically to enter the secondary menu, and similarly, when the flash can be switched by K1, such as **0i, **0p, has the right to debug, please wait , the system will automatically exit the menu. (Using the skills, if choosing the right input channel, such as *-channel RGBS, can cut off the power, restart, the system will automatically identify the signal formats, such as the **0P.) 6, Control Software Description: 　　 RS**2: for serial debugging software, please download the software ***** may also be available to my company, can be adjusted up and down about the size, color, contrast, brightness, etc. At the same time, scalable systems, ***6 products can be upgraded features, and performance, such as a special field trip, not normal use by the debugging software company, distributed to customers directly by the customer to upgrade. Also has the function of conservation and load, if you set more than one machine, as long as there is a good one, all others can be COPY, if the wrong tune, you can restore the factory settings. We will provide products in each article **2 debug serial line, on behalf of users. Description: The manufacturers of products for each signal source is likely not the same as, the need for debugging, for example, is very important to download the software image to be compressed, or the left, right, etc., please use the software to adjust. If you are not completely normal. 7, the corresponding video format definition line field: The circuit board has been preserved in the internal signal parameters the following parameters, you can directly support the following resolution signal. Line-frequency field frequency corresponding to OSD ****0, *0, //#define _**0i*0 0 ****5, *0, //#define _**6i*0 1 ****5, *0, //#define _***0i*0 2 ****0, *0, //#define _***0i*0 3 ****0, *0, //#define _**0p*0 4 ****0, *0, //#define _**6p*0 5 ****0, *0, //#define _**0p*0 6 ****0, *0, //#define _**0p*0 7 ****0, *0, //#define _***0p*0 8 ****0, *0, //#define _***0p*0 9 New procedures are: line frequency of *0Hz field frequency *1.8KHz and *4.9KHz line frequency *6Hz field frequency, etc. And can be upgraded in accordance with the requirements needed for other procedures, some special signal source customers can contact us to upgrade the program in order to achieve the best effect. 8, the technical parameters Power: DV*2V, *2 DC, recommends that more than 1A current. Input video signal: Support (CGA, EGA, RGB, RGBS, RGBHV, YUV, etc.) Support, **0I, **6I, **0I, ***0I, **0P, **6P, **0P, ***0P, etc. Peak signal: 1.5Vpp Impedance: *5Ω Level:0.***3.5 Signal output: Interface: VGA Resolution: ***4 * **8 Refresh Rate: *0HZ Informationï&frac*4;š Please reply to ***** or *****