Description
Description:
VAG Vehicle Diagnostic Interface VVDI Newest update:
1.
Support NEC *4C*2 change mileage through obd2, generate dealer's
keys, read and write EEPROM and backup flash data.
2. Support GOLF5 MM7(9S*2) change mileage through obd2, generate
dealer's keys, read and write EEPROM and backup flash data.
3. Add TA special chip pre-program. Directly pre-program ID*8 to
TA2,TA3, TA4, TA5 chips.
Attention: IMMO
PLUS 2.0 software and VAG Commander software can use VVDI hardware
together, but previous VVDI customer need update hardware then can
support IMMO Plus software.
Now IMMO PLUS has been updated to V4.0. Please download from our
website to update.
Function:
1) Extracting security access codes (PIN) by OBDII
2) Programming keys by OBDII. Preparation of dealer's keys.
3) Mileage recalibration by OBDII
4) Clearing crash data DTCs by OBDII
5) Read/Program flash memory of engine control units by OBDII.
Options for resetting the number of flashing attempts.
6) Exchange speed limit of MMI-TV system
1.Standard diagnostic functions:
1) Connect to
the device using KWP***0 over TP2.0, KWP***0 over TP1.6, UDS over
ISO transport protocol (CAN), KWP***1 or KWP***0 over K-Line
2) For all electronic control units reading identification data
3) For all electronic control units read error (DTCs)
4) For all electronic control units clear error (DTCs)
5) Scan all units
6) Broadcast requests
7) Measured values
8) Adaptation
2.Special functions:
1) Instrument CAN
(1) With this function you can establish diagnostic session with
the Instrument cluster using KWP***0 over TP2.0
(2) You can read current odometer value
(3) You can change odometer value
(4) Added support for VDO Instrument Cluster ***6+
(5) Read/Program memory of instrument cluster immobilizer
(6) Reading security access code of the IMMOBILIZER
(7) Read/Write immobilizer related data
2) EZS - Kessy (Q7/A6/Allroad)
(1) With this function you can prepare dealer key/learn dealer
key
(2) Read/Write eeprom from EZS - Kessy (Q7/A6/Allroad)
3) Instrument K-Line
(1) With this function you can establish diagnostic session with
the Instrument cluster via K-Line (KWP***1 or KWP***0)
(2) You can Read/Change odometer value
(3) Read PIN code
(4) Read/Write eeprom
(5) Read ROM/Flash from the Instrument cluster
4) Engine Control Unit
(1) Read EDC*7/MED*7 flash memory
(2) Read/Write of flash memory (EDC*5, EDC*6 all types Read/Write
Flashmemory via OBDII (K and CAN). Calculation of checksums while
programming, ME7.1.1, MED9.x, ME7.5)
(3) Read/Write flash counters (EDC*6)
(4) Read/Write eeprom (VAG-EDC*5x, VAG-ME7.1.1, VAG-ME7.1,
VAG-ME7.5, VAG-Cartronic ME7.8.)
(5) Extracting Security access code / PIN (EDC*5, ME7.x,
VAG-Cartronic ME7.8, EDC*6, EDC*7, MED9.x, Simos PPD)
(6) Extracting Component security bytes (EDC*5, ME7.x,
VAG-Cartronic ME7.8, EDC*6, MED*7.5.1, MED 9.x, Simos PPD)
(7) Enable/Disable immobilizer (EDC*5, ME7.x, EDC*6)
(8) Odometer correction (EDC*5, EDC*6)
5) Kessy adaptation
This function can be used for adaptation of brand new kessy units
to the car. This adaptation can be by CAN TP2.0, K-KWP***0 and also
can be used with Porsche Cayenne.
6) TV activation ED1/ED2
(1) Using this special function you can change speed limit of MMI
compatible vehicles to change speed where TV becomes OFF
7) Key learning
With this function you can learn key/transponder to the vehicle
8) Dump tool
With this function you can calculate security access codes, change
odometer and so on from EEPROM dump from the corresponding unit
9) Airbag
With this special function you can Read/Write EEPROM memory of the
airbag module
Clear the crash data of the airbag module
*0) Custom Read/Write
Using this application you can read/program memory in some
electronic control unit
*1) PIN Convertor
*2) Service interval
Using this function you can perform reset of the service reminder,
reset of the service interval parameters or change service interval
options
*3) Remote control adaptation
Using this application, you can learn remote controls
*4) Navigation
Using this application, you can enable/disable the “Eject” button
of the “Navigation” system
*5) Cruise control system
Using this application, you can activate/deactivate a cruise
control system and change the related
steering wheel electronics( SWE) configuration if SWE unit is
available
Function in addition:
1.According to obd2, the latest VVDI supports nec
*4c*2 mileage change, dealer key generation, EPPROM data reading
& writing, FLASH backup.
2.According to obd2, the latest VVDI supports GOLF6 MM7(9S*2)
mileage change, dealer key generation, EPPROM data reading &
writing, FLASH backup.
3.Add the function of professional TA chip pre-program, it directly
pre-programs *8 chip into TA2, TA3, TA4, TA5.
If any inquiry please check EOBD2 site
