Description

VAG VVDI Interface VAG Commander 8.6  
VAG Commander 8.6 update to  VAG VVDI interface
 VAG COMMANDER V8.6 updated to VVDI interface.
 do you know what the VVDI interface is ?
VVDI *-VAG Vehicle Diagnostic Interface  
 VAG VVDI interface can be compatible with abritus commander for vag ,and ADD other software to programmer keys and mileage corrections,abritus vag commander donot have those functions .this VVDI interface can run abritus vag commander software ,but abritus hardware cannot run VVDI's software.from this ,you can see that our VVDI interface is much more stronger than abritus commander for VAG
for more software update information,welcome to download the PDF file from our website . OBDIICHINA Commander for VAG is a Windows PC based diagnostic software for the vehicles from VAG. With the help of this tool you can perform operations with vehicles from the VAG group, which are in most cases unsupported from the producer diagnostic testers. The ABRITES Commander for VAG provides you also a full diagnostic capabilities for VAG-vehicles. Standard diagnostic functions:
Connect to the device using KWP***0 over TP2.0, KWP***0 over TP1.6, UDS over ISO transport protocol (CAN), KWP***1 or KWP***0 over K-Line 
For all electronic control units reading identification data 
For all electronic control units read error (DTCs) 
For all electronic control units clear error (DTCs) 
Scan all units 
Broadcast requests 
Measured values 
Adaptation 
Special functions: Instrument CAN
- With this function you can establish diagnostic session with the Instrument cluster using KWP***0 over TP2.0
- You can read current odometer value
- You can change odometer value
- Read/Program memory of instrument cluster immobilizer
- Reading security access code of the IMMOBILIZER
- Read/Write immobilizer related data EZS - Kessy (Q7/A6/Allroad)
- With this function you can prepare dealer key/learn dealer key
- Read/Write eeprom from EZS - Kessy (Q7/A6/Allroad) 
Instrument K-Line
- With this function you can establish disgnostic session with the Instrument cluster via K-Line (KWP***1 or KWP***0)
- You can Read/Change odometer value
- Read PIN code
- Read/Write eeprom
- Read ROM/Flash from the Instrument cluster Engine Control Unit
- Read EDC*7/MED*7 flash memory 
- Read/Write of flash memory (EDC*5, EDC*6 all types Read/Write Flashmemory via OBDII (K and CAN). Calculation of
checksums while programming, ME7.1.1, MED9.x, ME7.5) 
- Read/Write flash counters (EDC*6)
- Read/Write eeprom (VAG-EDC*5x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8.) 
- Extracting Security access code / PIN (EDC*5, ME7.x, VAG-Cartronic ME7.8, EDC*6, EDC*7, MED9.x, Simos PPD) 
- Extracting Component security bytes (EDC*5, ME7.x, VAG-Cartronic ME7.8, EDC*6, MED*7.5.1, MED 9.x, Simos PPD)
- Enable/Disable immobilizer (EDC*5, ME7.x, EDC*6) 
- Odometer correction (EDC*5, EDC*6) 
Kessy adaptation
- This function can be used for adaptation of brand new kessy units to the car. This adaptation can be by CAN TP2.0, K-KWP***0 and also can be used with Porsche Cayenne. 
TV activation ED1/ED2
- Using this special function you can change speed limit of MMI compatible vehicles to change speed where TV becomes OFF 
Key learning
- With this function you can learn key/transponder to the vehicle 
Dump tool
- With this function you can calculate security access codes, change odometer and so on from EEPROM dump from the correcponding unit 
Airbag
- With this special function you can Read/Write EEPROM memory of the airbag module
- Clear the crash data of the airbag module 
Custom Read/Write
- Using this application you can read/program memory in some electronic control unit 
PIN Convertor 
Service interval
- Using this function you can perform reset of the service reminder, reset of the service interval parameters or change service interval options 
Remote control adaptation
- Using this application, you can learn remote controls 
Navigation
- Using this application, you can enable/disable the Eject button of the Navigation system 
Cruise control system
- Using this application, you can activate/deactivate a cruise control system and change the related
steering wheel electronics( SWE) configuration if SWE unit is available 
Brake pads change
- Using this application, you can Open rear parking brake for pad change, Close rear parking
brake, perform Parking brake function test   VAG  VAG COMMANDER 8.6 LICENSE
1 AN**2 - KM-CAN 
1 AN**3 - PIN-CAN
1 AN**4 - IMMO panel 
1 AN**5 - IMMO panel EDC*6 
1 AN**6 - KM/PIN K-Line 
1 AN**8 - Flash Counters
1 AN**9 - Key learning 
1 AN**0 - Airbag EEPROM 
1 AN**1 - TV Activation 
1 AN**2A- EDC*6 Odometer 
1 AN**2B- EDC*6 EEP/PIN/IMMO-off 
1 AN**4 - EDC*7 EEPROM 
1 AN**5 - Flash Memory ECU 
1 AN**6 - Dealer key learning 
1 AN**8 - Dealer key learning Q7 
1 AN**9 - Prepare Dealer Key Q7 
1 AN**1 - ME7 EEPROM by CAN 
1 AN**2 - CDC*2xx Programmer 
1 AN**7 - Q7 ***8 Update steps:
1. install commander update 1.3 software, click [read sn] to get serial numberabout one min..
2. give serial number to your supplier, they will send you update software
3. install commander update 1.3 software, click [read sn] to get serial number, then click [UPDATE] and choose latest software, click [OK], and software starts update
4. After update, there is notice message [UPDATE OK]  VVDI is the short of VAG Vehicle Diagnostic Interface acronym, it is a common diagnostic interface made from China, which is not **0% clones hardware. The VVDI diagnostic interface works with own VAG IMMOPLUS software, you can also use the VAG COMMANDER 8.6 software, it is 2 in 1 interface working with two softwares at the same time. This interface owns more functions than separate vag commander 8.6 or vag immo plus. It will be more useful for customers. Working with VAG IMMOPLUS software, it will support more models of CDC*2XX ,NEC*4C*4, golf 6 mm7. This interface can be updated, it will support more car models later, and update free in one year. VVDI latest upgrade Update on May *0: 1. Bora 1.4T NEC*4C*2 model was added
2Q7, A6L models after Year ***9 were added 
*************************************************- *********- 
Update April *0
1. Support NEC*4C*2 miles Model ,creat agent keys, EPPROM data read and write, Copy FLASH BY OBD.
2. Support GOLF6 MM7(9S*2) miles Model ,creat agent keys, EPPROM data read and write, Copy FLASH BY OBD2.
3. Increase pre-programmed TA-specific chips , programmed chips *6 to TA2, TA3, TA4, TA5 chip. 
*************************************************- *********- 
VAG IMMO PLUS software
1. Support cdc*2xx of Year ***6 , mileage changes, creat keys, EPPROM data read and write, FLASH data read.
(More HASH KEY than vag commander, more algorithms, support for more models, and if do not to support the miles, you can use XPROG data to flash and send you EPPROM to agents, we will try to update
2. Support nec*3c*2 of Year ***8 , mileage changes, creat keys, EPPROM data read and write, FLASH data read.
3. Support nec*3c*4 of Year ***0 , mileage changes, creat keys, EPPROM data read and write, FLASH data read.
4. Support golf6 mm7, mileage changes, creat keys, EPPROM data read and write, FLASH data read.
5. Support the chip of TP series production, tp*2, tp*3, tp*4, tp*5 
6. Support the chip of TA series production, ta2, ta3, ta4, ta5