Description
SRT****0 Portable Surface Roughness Tester
1.FEATURES
This instrument is compatible with four standards of site to
measure surface roughness of various machinery-processed parts,
calculate corresponding and clearly display all measurement
parameters.
When measuring the roughness of a surface, the sensor is placed on
the surface and then uniformly slides along the surface by driving
the mechanism by the sharp built-in probe. This roughness causes
displacement of the probe which results in change of inductive
amount of induction coils so as to generate
analogue signal, which is in proportion to the surface roughness at
output end of phase-sensitive rectifier. The exclusive DSP
processes and calculates and then
outputs the measurement results on LCD.
* Multiple parameter measurement: Ra, Rz, Rq, Rt
* Highly sophisticated inductance sensor
* Four wave filtering methods : RC, PC-RC,
GAUSS and D-P
* Built-in lithium ion rechargeable battery and control
circuit with high capacity
* Small in size, light in weight and easy to use
* Can communicate with PC computer for statistics,
printing and analyzing by the optional cable and the
software for RS**2C interface.
*Manual or automatic shut down. The tester can be
switched off by pressing the Power key at any time.
On the other hand, the tester will power itself off
about 5 minutes after the last key operation.
*The tester can memorize 7 groups of measurement
results and measuring conditions for later use or
download to PC.
*Metric /Imperial Conversion
2.SPECIFICATIONS
Display: 4 digits, *0 mm LCD, with blue backlight
Parameters: Ra, Rz, Rq, Rt
Measuring Range
Ra, Rq: 0.*****6.*0um/0.******9.9uinch
Rz,Rt: 0.******0.0um/0.*******9uinch
Accuracy: ≤±*0%
Fluctuation of display value: Not more than 6%
Sensor :
Test Principle: Inductance type
Radius of Probe Pin: 5um
Material of Probe Pin: Diamond
Dynamo-measurement of Probe: 4mN(0.4gf)
Probe Angle: *0
Vertical Radius of Guiding Head: *8mm
Maximum driving stroke: *7.5mm/0.7inch
Cutoff length (l): 0.*5mm / 0.8mm / 2.5mm optional
Evaluation length: 5l
Driving speed:
sampling length = 0.*5mm Vt=0.**5mm/s
sampling length = 0.8mm Vt=0.5mm/s
sampling length = 2.5mm Vt=1mm/s
returning Vt=1mm/s
Profile digital filter
Filtered Profile: RC
Filtered Profile: PC-RC
Filtered Profile: Gauss
Non-Filtered Profile: D-P
Resolution : .**1μm if reading less then*0μm
0.*1μm if *0μm≤reading less then **0μm
0.1μm if reading ≥**0μm
Evaluation length : 5 cut-off
Power Li-ion battery: rechargeable
Operating conditions: Temp. 0~*0C
Humidity <*0%
Size:**0x*7x*8 mm (5.5x2.2x1.9 inch)
Weight: about **0 g
Attachment:
Standard Sensor RP***0
Groove Stylus SRP***0
curvature Probe SRP***0
Extension Rod SER***0
Mesurement Stand SRS*1
Standard Sample Plate SSP***0
Cable and Software for RS***2/USB
Bluetooth interfaceModel:DT***0P
Measurement Range:A:*0~****0FPM
B: *0~****0 FPM
C:*0~****0 FPM
D:*0~****0 FPM
E:*0~***0 FPM(fit for print and textile)
Display:5 *0mmLCD
Accaracy:*-(0.*5%n*1d)
Resolution:0.1 FPM( Less ***0 FPM)
1 FPM(Over ***0 FPM)
Sampling time:0.3second
2 ranges:Hã€L ( High,Low )
Flash adjust:Coarse adjustmentã€fine adjustment , *2 and / 2 for
fast check
Triggering Mode:Interior/Exterior
Temperature:0~*0C
Humidity:Less than *5%RH
