Description
The Designed for cylinder without sensor or hydraulic
cylinder
1, Introduction
1. JMDM*4D dynamic cinema control software has two parts:
edit-end (JMDM*4Dfilm editor) and client-end (JMDM*4Dfilm
player)
. Coordinate of JMDM series of many types industrial 4D seat
special ef-fect equipment to use , consist of JMDM 4D
cinemas
seat special equip-ment control system. One set of system
configuration: one editor and one player software
opening
jurisdiction. Usually match one Dog used to open the editor
and the player software. Can also according to the cus- tomer
requirements add one, that is one Dog used to open
editor soft-ware and the other one is to open player
software.
Function as follows:
1, Used for 4D cinema manufacturers, used in edit the dynamic
seat and special effect equipment of the 4D
three-dimensional
film synchronize act with the cinema plot, also can play
edited special effect movie, to test the effect.
2, Editing special effect in the software interface when see
the movie; or edit motion through generated motion file.
3, Realized functions: making the seat special effect, film
three-dimensional pictures of the three-dimensional 4D
dynamic
film closely combined with the film plot, can easy to edit
seat and special effect motion: shock, jolt, drop,
storm,
thunder , rain, hit, spraying water mist, pat leg, jet, smoke,
snow, smell, spray wind, bring the audience dreamlike
and
exciting amusement.
Second, the Instructions
1, Install Dog drive
Please run the drive install program (DogInst.exe) which
supplied by our company at the first use, click install after
the
program running.
2 According to MSCOMM*2
If the players double clicked with no response after
the drive installed, please install MSCOMM*2 again; if it is
present
a inefficient port number, just change the com5 of the file
config.ini into the port using in the computer.
(Examine
methods of the 'com'port: the right button of' my computer '→
equipment manager → port).
3, Insert the Dog
It must insert the Dog No matter running the JMDM*4D special
ef-fect edit-end or the client-end software, otherwise the
program can not running; and cannot pull out the Dog
when the program running.
4, Edit software and player software and operation
explanations
Divided into two categories according to the cylinder:
cylinder with electronic scale, cylinder without electronic
scale.
Choose the controller according to the difference of the
hardware and software.
5, Insert the Dog
It must insert the Dog when running the JMDM*4D special effect
edit-end play software, otherwise the program can not
running; and cannot pull out the Dog when the program
running.
Third, the 4D film edit-end operation explanations
**1 corresponding controller "circuit for each check box check
box (tick represent open the circuit, on the contrary,
represent the close the circuit)
Cylinder 1 up **- → → the path a four path the one cylinder
down **-
Cylinder down - → path two cylinder up ***- → path at
five
→ cylinder 2 up ****- → path of three cylinder down - the path
six
The other circuits are corresponding with the interface
(Customers can provide themselves' wiring situation to us; we
can modify into correspondence name, for example, special
effect path *1 changes into spray and so on)
(If that is two paths control one cylinder; cylinder turn to
up / down, tick the box before the cylinder up / down,
stopping the cylinder need to removed all of the cylinder up /
down ticks)
If that is one path control one cylinder, connect the wiring
in or-dered, for example, cylinder one up connect
cylinder
one down and cy-linder one down connect cylinder two
up.etc.
**2 of The function for the each button as follows
1. â–² open file button: choose the movie file which needs to
edit motion in the popup dialogue box.
2 the ◣ the play / 〓 the pause: Can the play or the pause
film playing, add motion only in the the pause state.
<Back /> next: can forward or backward to the position
of 0.1 second.
4. After playing at the appropriate position, choose the
motion which need add, then click'add motion'button,
popup'motion
successfully added'means the motion at this time has finished.
(Tick means path one open, on the contrary it means the
close)
5. THE LAST MOTION: click the last motion button can skipped
to the former motion
6. THE NEXT MOTION: click the next motion can skipped to the
next one motion
7. GO: click the go button can skipped to the input time of
the input form.
8. SAVE MOTION: click save the motion button auto save the
motion to the film list after all the motion have finished
edited
(motion file is (*. Jm It will be better that save a motion
after adding a dozen motions)
9. DELETE MOTION: Skip to the time then click the delete
motion button can delete the current motion when the motion is
not
wanted to. (Can revise the click add button directly if it
just want to revise the motion, and then it finished)
**3 Examples for the edit motion
To take edit Adventures of iceberg.avi: the
three-dimensional film for example (to take two path control one
cylinder for
in-stance)
1. Click the open file button, skipped / bring out a dialogue
box as shown. Choose Adventures of iceberg.avi, click
open
button.
2. Click the play button / pause button: Can play or pause
film playing, add motion only in the pause state.
Make the cylinder up at the position of 1.0 seconds
a. Click forward or backward button to the position of 1.0
seconds, or input 1.0at the edit dialog box and click the
GO
button to bring out the position of 1.0s
(b) the Tick cylinder the one up, as shown.
c. Click ADD MOTION button add motions, that finished the
mo-tion at the position of 1.0s
Make cylinder the one up and cylinder two down at the position
of 2.0s
a Click the NEXT to the position of 2.0s
b. Taking off the tick of the cylinder one and tick the
cylinder one down and cylinder two up. As shown.
c click the ADD MOTION to add the motion.
TO make cylinder the one stop cylinder two down, cylinder
three up at the position of 3.0s
a Click the NEXT to the position of 3.0s
b. Taking off the tick about the cylinder one down and
the cylinder two up, tick the cylinder two up and the
cylinder
three up, as shown.
c click the ADD MOTION to the add motions
6. Making the cylinder two stopped and the cylinder three
continue to up, spray at the position of 4.0s
a Click the NEXT to the position of 4.0s
b. Taking off the tick about cylinder two down and tick
electric machine one, as shown.
c click the ADD MOTION to the add motions
7. Repeat the above steps, after finished editing the motion,
click SAVE MOTION to save the motion as files. The file
name
of the motion file is' Adventure of iceberg.jm. And Adventure
of iceberg.xls. Xls file just use to The earliest
convenience
the editor check the motion.
