タイトルまたは説明
Rubber
Airbag Introduction:
Rubber Airbags, basic body consists of rubber layers,
synthetic-cord-reinforced rubber layers, are kind of a cylindrical
airbags with hemispherical heads at the both ends. All of these are
vulcanized together, and then compress air inside to enable in to
roll.
Rubber
Airbag Parameter: ( we can supply detailed dimension )
|
Diameter (D):
|
From 0.5m to 2.8m
|
|
Effective Length (EL):
|
From 5.0m to *4.0m
|
|
Total Length (TL):
|
From 6.0m to *5.5m
|
|
Standard Number of Layers:
|
Usually ***0 layers
|
|
Loading Capacity:
|
About ****0 T/M
|
Rubber
Airbag Advantages:
Different airbag size stock available, quick delivery
Provide repair kit and on site instruction
Long time service life can be reused many times
Wear resistance and anti aging
Good raw material and cord fabric
Do no harm to the environment. Time & money saving
Need no more than air compressors, winches and ropes
Marine airbags are much cheaper and portable than other methods
Rubber
Airbag Materials:
An airbag is to be constructed of an outer rubber layer, one or
more synthetic-tyre-cord layers, and an inner rubber layer. The
arrangement of synthetic-tyre-cord reinforcement layers is shown in
the picture below, all materials shall be vulcanized firmly.
Prior to the airbag production, the outer and inner rubber layers
shall be tested to meet criteria in the following table
in accordance with the test methods given in the
international standard list in the table.
While only one satisfactory sample per batch is required for test
numbers 1 through 3, all others must be tested for test numbers 4
through 9 annually. If the first sample fails, two additional
sample should be tested. If the additional samples pass the test
requirements, the materials will be deemed to have passed the test.
Otherwise, the materials will be deemed to have failed the test and
another batch of materials shall be selected.
Rubber Airbag Test:
unless otherwise specified, test shall be performed under the
following conditions: ambient temperature ****5. Media: dry clean
compressed air, and clean fresh water for bursting test. The test
should be performed using a full sized airbag. If the airbag is too
large to be mounted on the test machine, they test may be performed
on a scaled-down airbag. In order to maintain a proper
representation of the full-size sample airbag, the diameter of the
scaled-down airbag shall be no less than 1/2 of the full sized
sample airbag diameter, while the length shall be no less than 3
times the diameter of the scaled-down airbag.
Gas-tightness test
Without carrying any load, fill the airbag till the internal
pressure of the airbag in the following tale. The internal
pressure should be recorded and compared with the pressure
after 1 hour. The pressure loss should be less than 5% of
pressure.
Rubber Airbag Application:
1.For ship upgrading, conversion or new/repair launching
(Ship launching airbags)
2.Marine airbag for salvaging sunken ship or heavy immersed
steel structure
3.For hoisting and transporting heavy goods up to *0,**0
tonnes structure on land
4.Marine pneumatic rubber fender for protective purposes,
ships collision avoidance
5.Pneumatic rubber core for architecture
engineerinContainer for storing and transporting gas and
corrosive chemical liquid and pure water for voyage
6.Rubber bag for ship ballast
Rubber
Airbag Safety &
Storage:
Rubber Airbags Safety
precaution:
Over pressure Control:
Strictly control the operating pressure, over pressure is
forbidden.
The Landing Slipway Requirements:
The landing ground should be ground or cement concrete,
according the tonnage of different ships.
Avoid Sharp Objects:
Make sure no sharp objects and make sure the smooth and clean
ground during using them in case of break of airbag.
Avoid Distortion And Overweight
Avoid distortion in the length direction during rolling and
avoid overweight load after gas charging.
Rubber Airbags
Storage:
The airbags should be maintained in a dry ventilated room
and be protected from light.
The airbags should be in a relaxed condition free from
tension, compression or other deformation.
The airbags should be kept away from any heat source.
The airbags should be protected from acids, alkalis, oils or
organic solvents.
| 国: |
China |
| モデル番号: |
FL-JZY MDA1 D1.5*L14m
|
| 离岸价格: |
1000 ~ 2000 / Piece （交渉可能）
Get Latest Price
|
| ロケーション: |
- |
| 最低注文量の価格: |
1000 per Piece |
| 最低注文量: |
1 Piece |
| パッケージの詳細: |
Folded by rope without air or according to customers' demands |
| 納期: |
Within 20 days after receiving payment |
| 供給能力: |
500 Piece per Month |
| 支払いタイプ: |
Other, PayPal, Money Gram, Western Union, L/C, T/T |
| 製品グループ : |
- |
